Peugeot 308 reliability

Vehicles may be affected by premature wearing of the camshaft drive chain leading to abnormal noise or to a breakage of the chain in the worst case.

Fix: Update the software to improve oil pressure and reduce wear. Check the engine noise and replace the chain if required. If no problem found change the oil to one with higher viscosity and special anti-wear additives.

Recalled models: 308 · 7,383 vehicles

On affected vehicles the exhaust temperature might be too low. This may lead to unrobust environmental performance.

Fix: Update the engine software.

Recalled models: 308 V2 · 2,113 vehicles

Affected vehicles may face potential leakage of the under-bonnet fuel pipe due to a weakness of its crimping.

Fix: Change the fuel pipe.

Recalled models: 308 · 3 vehicles

Affected vehicles may not comply with test requirements in the matter of emissions test execution by competent authorities and energy consumption may be too high.

Fix: Update the electrical Vehicle Control Unit (eVCU) software.

Recalled models: 308 · 307 vehicles

Affected vehicles have been equipped with a door control unit which does not have the latest software version.

Fix: Update the door control unit software on the driver and passenger side.

Recalled models: 308 · 2,529 vehicles

On affected vehicles equipped with E-call the device may not function when trying to connect to E-Call (Emergency Call) and B-Call (Breakdown Call) due to incorrect BSRF (On-board radiocommunication transmitter) configuration and as a result does not comply with regulatory requirements.

Fix: Check and replace the Radio frequency connectivity box.

Recalled models: 308 · 2 vehicles

Affected vehicles may have been built with an incorrect rear axle weight value recorded on the Manufacturer VIN Label.

Fix: Check Manufacturer VIN Label rear axle weight and replace the label if necessary.

Recalled models: 308 V3 · 28 vehicles

On affected vehicles due to a potential lack of electric parking brake application when the driver presses the throttle pedal to start driving from a parking position on a slope the vehicle could move in the opposite direction until the driver pushes the brakes and stops the vehicle.

Fix: Update the MCU (Motor Control Unit) with modified software.

Recalled models: 308 Electric · 76 vehicles

Affected vehicles may have an incorrect torque on several fixation points which could result in reduced control of the vehicle and overheating of electrical connections.

Fix: Check and tighten fixings to correct torque.

Recalled models: 308 V3 · 9 vehicles

On the affected vehicles the operation of the brake vacuum pump may be affected by material detaching from the timing belt caused by the ageing of the engine oil.

Fix: To rectify this issue a software update will be downloaded which will improve the vacuum diagnosis (in order to warn earlier about the risk of loss or reduction of braking assistance). The timing belt will be checked and if needed replaced with other components of the braking assistance system and the vacuum pump.

Recalled models: 308 V2 · 952 vehicles

On the affected vehicles the operation of the brake vacuum pump may be affected by material detaching from the timing belt caused by the ageing of the engine oil.

Fix: To rectify this issue a software update will be downloaded which will improve the vacuum diagnosis (in order to warn earlier about the risk of loss or reduction of braking assistance).

Recalled models: 308 V2 · 25,148 vehicles

The external door handle sliders might not be manufactured to the correct specification.

Fix: Check the production date stamped on the door handle slider and replace the slider if needed.

Recalled models: 308 V3 · 17 vehicles

The brake vacuum pump may be affected by material detaching from the timing belt.

Fix: Update detection software inspect and if necessary replace vacuum pump and timing belt.

Recalled models: 308 V2 · 22,580 vehicles

The filtering performance of the Diesel Particle Filter (DPF) may not meet the required specification.

Fix: Replace the DPF on affected vehicles.

Recalled models: 308 · 959 vehicles

There is a possibility that the internal corrosion protection of the front subframe is not durable enough.

Fix: Replacing the front subframe assembly.

Recalled models: 308 (T9) · 38 vehicles

Engine management software issue could cause damage to the diesel particulate filter.

Fix: Replace the filter and update the engine management software.

Recalled models: 308 · 117 vehicles

The calibration of the engine management software could result in emissions of NOx which do not comply with the regulatory limits.

Fix: Download new engine management software

Recalled models: 308 · 9,218 vehicles

A plastic component inside the exhaust line could under certain conditions damage the Diesel particle filter.

Fix: Check and if necessary replace the particle filter.

Recalled models: 308 · 2,686 vehicles

On the affected vehicles the tightening of a sealing plug on the engine oil gallery may not be correct to specification.This could lead over time to an oil leak which in rare cases could result in oil leaking on to the road.

Fix: The remedy consists of tightening the engine oil gallery sealing plug to the correct torque

Recalled models: 308 · 47 vehicles

Engine could overheat leading to failure in extreme cases

Fix: Download new engine management software

Recalled models: 308 · 683 vehicles

On the affected vehicles an internal component within the airbag triggering ECU may have been damaged which could lead to non deployment. There are no early warning signs or symptoms for the customer to indicate if the ECU is incorrect.

Fix: The manufacturer has no simple method to check the internal component. Therefore all ECU's in affected vehicles to be changed as a precaution.

Recalled models: 308 (T9) · 124 vehicles

The engine electronic cooling management control strategy and the maximum temperature alert threshold could cause the engine to overheat. This could result in a warning light and a message being displayed on the instrument panel.

Fix: On affected vehicles download a new engine management software in order to modify the cooling management parameters to improve the control of the engine operating temperature.

Recalled models: 308 (T9) · 1,579 vehicles

An engine component may not be to specification which could result in loss of engine performance. This may lead to the engine stalling and potentially causing an engine failure. In very unlikely circumstances the vehicle speed may increase without warning but will stop on its own after a few seconds.

Fix: On affected vehicles carry out a functional diagnostic check of the engine. If necessary replace the engine.

Recalled models: 308 (T9) · 416 vehicles

The positioning of the starter motor supply terminal may not conform to specification. Contact with a neighbouring component could cause a short circuit.

Fix: On affected vehicles check the position of the terminal and where necessary reposition. Replace damaged components if necessary.

Recalled models: 308 (T9) · 7,394 vehicles

The front suspension wishbone fixing bolts may have a non-conformity which could lead to a risk of them breaking. The driver would be aware of a change in the behaviour of the vehicle�s directional control.

Fix: On affected vehicles replace the front suspension wishbone fixing bolts

Recalled models: 308 · 1,051 vehicles

A possible nonconformity of an internal component of the starter motor relay could affect the control of the starter motor. This could adversely affect the starting operation and damage the starter motor due to overheating and in extreme cases there is a risk of fire.

Fix: On affected vehicles check and where necessary replace the starter motor relay.

Recalled models: 308 · 6,768 vehicles

A possible non-conformity in the fitting of the tyre valves as well as an incorrect tightening torque of the valve securing nut could cause a valve to fail and a rapid loss of pressure in the tyres. The tyre pressure monitoring warning lamp would illuminate to warn the driver.

Fix: On affected vehicles replace the tyre valves using a fitting jig.

Recalled models: 308 (T9) · 235 vehicles

The bonding of the tailgate components may not be to specification this could affect the retention of bonded parts over time. The owner could notice the individual components becoming loose or detached from the tailgate such as brackets bonded trim panels etc� If left unnoticed bonded items could become detached from the tailgate.

Fix: Recall the vehicles that are likely to be affected and replace the complete tailgate assembly.

Recalled models: 308 · 206 vehicles

The fuel injectors supply rail could develop a leak over a period of time leading to a drop in fuel pressure which can affect the operation of the stop start system. In some extreme cases the engine might not restart and a spray of petrol under the bonnet may occur which is a fire risk.

Fix: Recall the vehicles that are likely to be affected and check the fuel injector supply rail. Where necessary replace the fuel injector supply rail.

Recalled models: 308 · 86 vehicles

A manufacturing defect in one of the components of the door locks could cause jamming of the internal mechanism and prevent the closing of one or more of the vehicle's doors. In rare cases the door could unlock and open unexpectedly.

Fix: On affected vehicles check and where necessary replace door locks.

Recalled models: 308 (T9) · 679 vehicles

A manufacturing defect in one of the components of the door locks could cause jamming of the internal mechanism and prevent the closing of one or more of the vehicle's doors. In rare cases the door could unlock and open unexpectedly.

Fix: On affected vehicles check and where necessary replace door locks.

Recalled models: 308 · 1,176 vehicles

A manufacturing defect in one of the components of the door locks could cause jamming of the internal mechanism and prevent the closing of one or more of the vehicle's doors. In rare cases the door could unlock and open unexpectedly.

Fix: On affected vehicles check and where necessary replace door locks.

Recalled models: 308 (T9) · 1,347 vehicles

An oil leak could develop at the turbocharger lubrication union retaining bolt due to a non-conformity of this part.

Fix: On affected vehicles replace the turbocharger lubrication union bolt and its seals.

Recalled models: 308 · 25 vehicles

A manufacturing defect of a component within any of the four door locks could result in jamming of the internal mechanism which prevents the closing of any of the vehicle's doors or risk unexpected unlocking and opening of the doors.

Fix: Recall the vehicles that are likely to be affected to check and where necessary replace the affected door locks.

Recalled models: 308 (T9) · 1,369 vehicles

The fuel heating device integrated in to the diesel fuel filter cover may be defective and allow heat to build up within the electrical supply connector causing the cover to distort and air to enter the fuel circuit. This could make the vehicles difficult to start and a warning light will be illuminated on the dash board. The engine could be difficult or not possible to start. In the worst cases a diesel fuel leak could eventually appear.

Fix: Recall the vehicles that are likely to be affected and replace the fuel heater cover. Additionally the electrical connector will be inspected and where necessary replaced.

Recalled models: 308 · 12,833 vehicles

The fixing bolts of the front suspension wishbones may not be to the correct specification. This could lead to the bolts failing and the security of the wishbones being compromised. If this occurs there is a possibility that the directional control of the vehicle could be adversely affected.

Fix: Recall the vehicle that are likely to be affected and replace all the fixing bolts of the front suspension wishbones.

Recalled models: 308 · 14,840 vehicles

On affected vehicles the gear lever reverse locking ring might not be to the correct specification. This could cause difficulty in selecting first and reverse gear or an error when changing between 1st and reverse..

Fix: Replace the gear lever reverse locking collar.

Recalled models: 308 · 184 vehicles

It has been established that the high pressure fuel rail pipes on the engine have not been torqued to the correct specification. This can result in poor sealing of the rail which can cause as fuel leak onto the engine. If the vaporised fuel comes into contact with a hot engine component there can be a risk of an engine bay fire.

Fix: Recall all the affected vehicles and retorque the high pressure fuel rail pipes.

Recalled models: 308 · 148 vehicles

On the affected vehicles the rear screen seal may not conform which could lead to water ingress in the boot and poor ageing of the seal. In very rare cases the rear screen could detach.

Fix: Recall the vehicles that are likely to be affected to remove and refit the rear screen.

Recalled models: 308 · 18 vehicles

On affected vehicles the upper section of the front right shock absorber may not be correctly tightened. This could eventually cause noise or banging and if left may affect the efficiency of the shock absorber.

Fix: Replace the front right shock absorber.

Recalled models: 308 · 8 vehicles

It is possible the mountings for the steering mechanism to engine subframe may not have been torqued to the correct specification. If this is the case the issue will be highlighted to the driver by noise or play in the steering. If the driver fails to take action to rectify the issue the steering may detach causing a possible loss of control.

Fix: Recall affected vehicles to check the torque of the mountings and if necessay replace the steering mechanism.

Recalled models: 308 · 642 vehicles

On some 2.0 l HDI vehicles potential contact between the fuel return pipe and the diesel filter support may eventually cause the pipe to become worn through friction.

Fix: The manufacturer has requested that some protection be added to the pipe to ensure its long-term resistance to wear.

Recalled models: 308 · 2,834 vehicles

In very rare circumstances the vacuum pump one way valve may not function correctly which could affect the level of braking assistance.

Fix: Recall the vehicles that are likely to be affected to replace the brake vacuum pump one way valve.

Recalled models: 308 · 24,220 vehicles

In certain circumstances it is possible that the passenger could inadvertently apply the service brake. The linkage is accessed above the passenger footwell.

Fix: Affected vehicles will have a cover fitted above the passenger footwell to close off access to the brake linkage.

Recalled models: 308 · 13,263 vehicles

It has been identified that the position of the exterior lighting control ring may not be detected by the lighting management system and the lights may switch off without warning.

Fix: Recalled vehicles will have the lighting management software updated.

Recalled models: 308 · 2,903 vehicles

It has been identified that an incorrect version of the steering power assistance software has been uploaded.The effect of which may lead to stiffness within the steering system

Fix: Recalled vehicles will have a steering power assistance ECU upgrade.

Recalled models: 308 · 5 vehicles

It has been identified that the front seats may collapse without warning. due to an electrical control box software issue.

Fix: Recalled vehicles will have the seat electrical control box replaced.

Recalled models: 308 · 532 vehicles

It has been identified that the welds which secure the bonnet locking assembly may prove inadequate in use. This can result in difficulty closing the bonnet or failure of the lock to properly engage.

Fix: Recalled vehicles will have a strengthening component fitted to the bonnet lining to ensure that the trigger cable remains firmly secured to the bonnet. In very rare cases and only if necessarythe bonnet will be replaced.

Recalled models: 308 · 7,165 vehicles

In rare cases the lighting management system may incorrectly detect the lighting switch ring position which may cause the lights to cut out.

Fix: Recall affected vehicles and download new version of vehicle exterior lighting software.

Recalled models: 308 · 21,354 vehicles

An internal component of the Brake Master Cylinder may not be in conformity and as such braking performance/efficiency may be affected.

Fix: Recall affected vehicles and replace Master Cylinder.

Recalled models: 308 · 456 vehicles

It has been identified that the shield which protects the diesel fuel filter in the event of an impact may be incorrectly positioned. This can result in the possibility that the impact shield is in too close a proximity to the positive terminal of the alternator.

Fix: Recalled vehicles will have the position of the impact shield checked. Additionally the component will be fitted with an insulator.

Recalled models: 308 · 385 vehicles

It has been identified that use of a non standard interior lighting harness may cause excessive current flow and possible overheating and damage to a control unit This can result in the loss of a number of vehicle functions.

Fix: Recalled vehicles will have the subject wiring harness modified.

Recalled models: 308 · 13 vehicles

It has been identified that the main engine fuse box is not to the correct specification. This can result in operating faults or the failure of certain equipment.

Fix: Recalled vehicles will have the subject fuse box replaced.

Recalled models: 308 · 7,360 vehicles